Software > Software (16-/32-Bit)
1040ger als Router??
jens:
Habe auch gelesen, daß man für Mint ein größeres System und auch einen 030 haben sollte. Außerdem wird Mint wohl kaum ohne Platte laufen...
Ich denke, eine Lösung mit Sing wäre kein Problem, wenn es nur die entsprechende Software gibt. Und das weiß ich eben nicht...
SchwedeII:
Naja, Ihr habt Euch nun die Köpfe heiss geredet, folgendes:
STinG ist kein Problem, wenn es nur das auf dem STe ist. Bei MiNT kann ich mir ganz gut vorstellen, dass es geht, aber:
Freemint gibt es nur noch für den TT (68030 CPU Bedingung). Inwiefern ältere Versionen, ich hab noch alte MiNT-Sachen rumliegen, die Netzwerksachen überhaupt unterstützen, ich weiss es nicht. MiNT Treiber sind auf der Diskette von EH-Systems dabei. Auf jeden Fall gibt es da für mich 2 Probleme:
1. Ich hab mich noch nie mit MiNT beschäftigt (oder nur ganz kurz)
2. Wie kriege ich MiNT in eine Mini-Distri, ladbar von einer 720-ger Disk. Den STe hab ich ja noch nicht da, da kann ich nicht von ausgehen, dass da eine 1,44-ger drin ist.
3. Wenn ich nicht ganz klar weiss, ob ich unter MiNT eine Automation rein kriege, nützt mir das auch nix, da ich das gleiche auch noch nicht von STinG weiss. Genau darum geht es aber.
@ Johannes :- Spass machen muss das ganze wirklich nicht, es muss aber zuverlässig laufen. Momentan muss ich wieder von der Win-Dose meiner Gutsten schreiben, weil diese wieder mal mit der Netzwerkkarte nicht klar kommt und somit der Gateway und Proxy ausgefallen ist. Da krich isch'n Brechreiz!!!
Ich hab wie gesagt noch ältere MiNT-Versionen da(eine 0,x war damals noch PD, hab ich garantiert noch irgendwo. Hatte ich auch getestet, ging aber nur ohne Gem, da aber zuverlässig), wär doch mal'n geiles Projekt, ein "stiller" Router. Da kann doch mal angefangen werden, eine Mini-Distri für den STe zu entwickeln, fänd ich witzig, bräuchte aber mit Sicherheit Hilfe. Vielleicht wird so 'ne Console noch für andere interessant.
SchwedeII:
Hey, ich hab mal nachgeschaut, bei Mintnet 1.04 gibt es auf jeden Fall bereits eine automatische an- und Abwahl, nun muss ich mal nach dem Rest schauen.
Was brauche ich:
Kernel,
Treiber,
Kommandokonsole (bash)
und das Wissen, wie der Spass funzt. Mal schauen, wo ich 'ne Doku herkriege.
jens:
Hallöchen.
Ich weiß zwar nicht, ob es Dir weiterhilft, aber ich hätte da was zu dem Probem gefunden.
Masquerading is already built in in STinG. So it is possible to connect several computers together and use an Atari as Router.
Kenneth Medin from Sueden uses a 16 MHz Mega STe as router to the internet and a PC using Window$95 and a Stacy as networkclients.
Here you will find a discription on how to set up a similar network. It's a bit involved but should be correct.
It Works OK apart from the SCC gets overloaded with too high speeds.
There is no major speed penalty having both the attached PC and
Stacy downloading webpages at the same time.
Just as a Mega STe, the TT has several serial ports it is well suited for this.
You should start with setting up Sting for LAN use.
1. Decide ip addresses on your LAN:
Mega STe : 172.16.1.1
PC : 172.16.1.2
Stacy : 172.16.1.3
2. Edit Sting's ROUTE.TAB to
172.16.1.2 255.255.255.255 Ser.2/LAN 0.0.0.0
172.16.1.3 255.255.255.255 Modem 1 0.0.0.0
0.0.0.0 0.0.0.0 Masquerade 0.0.0.0
This is from my Mega STe so the port name Ser2/LAN will not be present on the TT.
You should use the exact spelling from the "Sting Port Setup" CPX.
Note that the modem port is not set here as we are using masquerade.
3. Open the CPX "Sting Port Setup"
For the two serial port in ROUTE.TAB set "IP Adress" to
172.32.1.1, MTU to 576 (1500 is default both in Sting and Win-95
and will work fine locally but if your isp uses 576 you will get
best resluts with the lower value). Select Active for both ports
and preferably SLIP without compression (PPP will work too, but
slower).
The serial port that is connected to your modem should NOT be
active! No IP address but with MTU=576 and PPP.
Select the "Masquerade" pseudo port IP address to 10.0.255.1
(default), MTU=576 and NOT active. Under "General" select the
serial port where your modem is connected and "Masking IP" to
10.0.255.0 (default).
4. Open the Sting Dialer and select "Configs" - "Miscellaneous".
Select the serial port where your modem is connected and select
"Use IP Masquerading"
5. Configure the Sting Dialer to conform to your isp's needs. For a
modern isp you will have to enter: MTU=576, PAP ID, PAP password
and select ppp in "Port Parameters". User name (account name), full
name and domain name in "Addressing". Nameserver can be left blank.
Full path for the file DIAL.SCR in "Miscellaneous". This is all you
have to set if your isp supports PAP. If you have managed to get
your pc connected you'll know what actual settings are needed.
6. Install either HSMODA7 or FASTSERIAL and set port speeds etc. I
have had some problems with HSMODA7 on the TT but Fastserial did
it's job too.
Win-95 side:
1. First you have to install a pseudo modem driver (MDMCBX4.INF) as
you will be using "dial-up network".
2. Install a new dial-up connection (your old one will still be
usable) and set it to uncompressed slip and fixed IP
address=172.16.1.2 (or 172.16.1.3). I think you must enter a
valid DNS address for the pc to resolve anything when online. Use
your ISP's DNS server.
3. Set the serial port speed on the pc to same as Atari. No
handshaking needed. Try first with a low speed (19200). I have
problems with the SCC in my MSTe (needs a ESCC) and get lots of
errors at higher speeds. (The Modem 2 port however works OK at
57600)
4. Open your prefered registry editor and make the necesserely changes
to get a MTU=576 :-)
There is a problem with the pc modem driver in that it needs some input
(anything will do) before it will connect so to get your network up and
running you'll need to:
1. Double click your new connection icon on the pc.
2. Open the Sting Dialer and select "Tools" - "Ping host". Enter the
pc IP address (172.16.1.2) and "Okay".
This will open a terminal window on the pc. select the button
"Continue" (or equal.) and your connection will be up.
Now you can run standard clients on your PC and Atari at the same
time connected to the Internet or just ftp localy between the
computers. The ftp server on Peter Rottengatter's (Sting) page works
fine. I have been less successful with aftp as client though. This runs
OK with Geneva+Neodesk on my network: PC + Mega STe + Stacy.
Geklaut von hier.
SchwedeII:
--- Zitat ---Hallöchen.
Ich weiß zwar nicht, ob es Dir weiterhilft, aber ich hätte da was zu dem Probem gefunden.
--- Ende Zitat ---
Sorry, aber da habe ich wieder das gleiche Problem.Das Masquerading von STinG nutzt zwar einen Dialer, aber auch dieser hat keine Möglichkeit, einzustellen, wann sich das Modem ein -und wieder abwählen soll. Und damit bin ich wieder am Anfang meiner Probleme.
Ich hatte eher so gedacht: Irgendeiner der Clients will in`s Internet. Der Router öffnet die Leitung.
!0 min keine Daten unterwegs: - der Router schliesst die Leitung. Ich hab alle Doku`s durchsucht, da nix beschrieben ist, vermute ich, dass es auch nicht geht.
Navigation
[0] Themen-Index
[#] Nächste Seite
[*] Vorherige Sete
Zur normalen Ansicht wechseln